Water Heater Temperature Problems Lehigh Acres FL Fixed Right the First Time
Hot water back to normal, usually the same day you call
Water Heater Temperature Problems Lehigh Acres FL means your tank is either scalding you at 150 degrees or handing you a lukewarm shower at 95. Both point to a thermostat, heating element, or gas valve that has drifted out of spec. We test the actual water temperature at the tap, diagnose the cause, and restore safe hot water, usually within a couple of hours.
What Water Heater Temperature Problems Lehigh Acres FL Actually Means
Water Heater Temperature Problems Lehigh Acres FL is a diagnostic and repair service that corrects hot water that runs too hot, too cold, or swings between the two. A tank should hold 120 degrees Fahrenheit at the tap. When it hits 140 or drops to 100, the culprit is almost always a failed thermostat, a burned-out heating element, a sticking gas valve, or sediment piled on the burner. We test with a calibrated gauge, not a hand on the pipe.
Lehigh Acres homes sit on hard, mineral-heavy well and municipal water, and that calcium settles at the bottom of every tank. Over two or three years that sediment layer insulates the burner, overheats the steel, and throws your temperature off. If your water heater water too hot Lehigh Acres or not hot enough Lehigh Acres, we flush the tank, test the thermocouple and TPR valve, and reset the thermostat to a safe 120 degrees. Most repairs finish in two to four hours.
Why Lehigh Acres Homeowners Call Us First
Temperature problems do not fix themselves, and a tank running at 150 degrees is a burn risk for kids and guests. Here is what you get when you book us.
Same-Day Hot Water
We stock Rheem, A. O. Smith, and Bradford White thermostats and heating elements on every truck, so most water heater temperature repair Lehigh Acres jobs finish in one visit. Call before noon and you usually shower normally that night.
Accurate Temperature Testing
We measure water at the nearest tap with a calibrated thermometer instead of guessing from the dial. You get a printed reading before and after, so you know the tank now holds 120 degrees and not 138.
Sediment Flush Included
Hard Lee County water leaves scale that fakes a thermostat failure. Every temperature repair includes a full tank flush through the drain valve, which restores heat transfer and adds years to the anode rod and glass lining.
Safe for Kids and Guests
Scald injuries happen above 130 degrees, and most are children under five. We set your thermostat to 120, confirm the TPR valve opens at the right pressure, and label the setting so nobody bumps it back up.
How Our Temperature Repair Process Works
You get a clear sequence from phone call to hot shower. No mystery, no waiting around all day for a window that never arrives.
Phone Diagnosis
You describe the symptom: scalding, lukewarm, or swinging temperatures. We ask the tank brand, age, and fuel type, then quote a realistic arrival window, usually within two to four hours for emergency water heater temperature repair Lehigh Acres FL calls.
On-Site Testing
Our technician measures tap temperature with a digital gauge, checks the thermostat setting, and tests the thermocouple or heating element with a multimeter. On gas units we inspect the burner flame and flue; on electric we ohm out both elements. This takes 20 to 30 minutes.
Repair and Replacement
We replace the failed thermostat, heating element, gas valve, or thermocouple using OEM parts matched to your Rheem, A. O. Smith, or Bradford White tank. A thermocouple swap runs 30 minutes; a lower element replacement takes about an hour with the tank drained.
Flush and Reset
We drain the tank through a hose to clear sediment, refill it, and set the thermostat to 120 degrees. The TPR valve gets a lift test to confirm it opens and reseats. You watch us take the final temperature reading so there is no doubt.
Walkthrough and Warranty
Before we leave, we show you the new reading, explain what failed, and hand you a written warranty on parts and labor. We also tell you the one maintenance habit that prevents the same failure, usually an annual flush.
Local Experience You Can Verify
Our technicians hold a Florida state plumbing license and a Lee County contractor license, and we work to the Uniform Plumbing Code and Florida Building Code on every job. Gas work follows ANSI Z21.10.1 and EPA Section 608 handling rules, and our installers carry NATE certification. We keep a thermocouple tester, multimeter, water heater element wrench, and inspection camera on every truck, so diagnosis happens on the first visit instead of a second trip. That local experience matters when your tank is 14 years old and parts are hard to match.
- Florida state plumbing license and Lee County contractor license held by every technician on staff
- NATE-certified technicians for gas and electric water heater diagnostics
- OEM parts stocked for Rheem, A. O. Smith, Bradford White, Rinnai, and Navien tanks
- EPA Section 608 and OSHA safety certification for gas appliance work
- Inspection camera used to check anode rod and dip tube condition before we quote
Why Water Heater Temperature Problems Lehigh Acres FL Homeowners Pick Us
We are a local shop, not a call center. The person who answers your phone is the person who knows your neighborhood and your tank.
Two-Hour Response
Emergency calls inside Lehigh Acres Central, Mirror Lakes, and Sunshine Acres get a technician on site in about two hours. We text you the tech name and arrival time so you are not guessing.
Upfront Flat Pricing
You get the full price before we touch a wrench. A thermostat replacement runs $180 to $320, and an element swap runs $220 to $450, parts included. No hourly meter, no surprise line items at the end.
All Brands Serviced
We repair Rheem, A. O. Smith, Bradford White, State Water Heaters, American Standard, Kenmore, Bosch, Rinnai, Navien, and Noritz units. Whether you need water heater temperature repair near me Lehigh Acres or a full tank swap, we carry the parts.
Workmanship Warranty
Every temperature repair carries a one-year labor warranty and the manufacturer parts warranty on top. If the same thermostat fails again within 12 months, we come back and make it right at no charge.
What Our Temperature Repair Service Includes
Every visit covers full diagnosis and the repair itself. If we find a cracked tank or a failed gas valve beyond economical repair, we tell you straight and credit the diagnostic fee toward the replacement.
What's Included
Full Temperature Diagnosis
Tap temperature reading, thermostat setting check, thermocouple or element test with a multimeter, and a burner flame inspection on gas units. You get the actual numbers, not a vague verdict.
Thermostat Calibration or Replacement
We reset your thermostat to 120 degrees or replace it if the contacts are pitted. Includes testing both upper and lower thermostats on electric tanks, since a single bad one causes wild swings.
Heating Element or Thermocouple Swap
Failed elements and thermocouples get replaced with OEM parts matched to your tank. We torque the element with a proper water heater element wrench so the gasket seals without cracking the glass lining.
Sediment Flush and TPR Test
Full drain and flush through the drain valve to clear calcium, then a lift test on the TPR valve to confirm it opens and reseats. This alone fixes many water heater water not hot enough Lehigh Acres complaints.
Safety Verification and Labeling
Final temperature reading documented, gas connections leak-tested with soap solution, and the thermostat dial labeled at 120 degrees so nobody accidentally turns it up to scalding.
Temperature Problems We Fix Every Week in Lehigh Acres
Most calls fall into four buckets. Here is what each one means and how we handle it.
Water comes out scalding at 140 degrees or higher
A tank running hot scalds children in seconds and stresses the TPR valve, which can start weeping or fail open. It also shortens the tank's life by cooking the glass lining.
We test the thermostat and gas valve, replace the failed part, and reset the tank to 120 degrees. On gas units a sticking gas valve is usually the cause; on electric it is a thermostat that has drifted or welded closed.
Shower goes lukewarm after five minutes
A failing lower heating element or a broken dip tube lets cold water mix into the hot outlet. You end up with a tank full of warm water that never reaches temperature.
We ohm out both elements, inspect the dip tube with an inspection camera, and replace what failed. Most water heater water not hot enough Lehigh Acres calls are a $220 to $380 lower element job.
Temperature swings between hot and cold
Wild swings usually mean sediment has built up on the burner or element, so heat transfer is uneven. Left alone, the tank overheats in spots and eventually leaks.
We flush the tank, inspect the anode rod, and test both thermostats. If the rod is under 50 percent, we replace it during the same visit to protect the tank lining.
Pilot light keeps going out on a gas tank
A failing thermocouple shuts the gas off, so you get no hot water at all. Relighting it works for a day or two, then it quits again.
We test the thermocouple with a dedicated tester and replace it, usually in 30 minutes. If the gas valve itself has failed, we quote the replacement upfront before starting.
When to Call Us for Temperature Repair
A family in Mirror Lakes has a 12-year-old Rheem tank that suddenly runs hot enough to steam the bathroom mirror.
We test the thermostat and gas valve, replace the failed thermostat, flush two years of sediment, and set the tank back to 120 degrees. Total time on site is about 90 minutes.
Water holds a steady 120 degrees, the scalding risk is gone, and the family avoids a $1,400 tank replacement for now.
A rental property near Joel Boulevard Corridor gets a tenant complaint that showers go cold after four minutes.
We diagnose a failed lower heating element and a partially broken dip tube, replace both with OEM parts, and verify the temperature at the tub spout.
Tenant gets full hot water through a 15-minute shower, and the landlord gets a written warranty to keep on file.
A homeowner in Varsity Lakes notices rusty water and a rumbling noise along with inconsistent temperatures.
We flush the tank, inspect the anode rod with a camera, and find it 80 percent consumed. We replace the rod, flush the sediment, and test both thermostats.
Rust clears within a day, the rumbling stops, and the tank gains another three to five years of service.
A snowbird returning to Lehigh Estates in October finds the tank has been off for months and now runs only lukewarm.
We relight the pilot, test the thermocouple, replace a corroded one, and run a full flush before restarting the tank.
Hot water is back the same afternoon, and the tank is verified safe before the homeowner unpacks.
Tools and Methods We Use
Tools & Equipment
Multimeter
Tests continuity and resistance on heating elements and thermostats to confirm which part has actually failed instead of guessing.
Thermocouple tester
Reads millivolt output on gas water heaters so we know whether the thermocouple or the gas valve is the real problem.
Water heater element wrench
Removes and torques screw-in heating elements without cracking the tank's glass lining or stripping the threads.
Inspection camera
Lets us look at the anode rod, dip tube, and tank interior through the fitting ports before quoting a repair or replacement.
Pressure gauge
Checks incoming water pressure and expansion tank charge, since high pressure can trip the TPR valve and mimic a temperature fault.
Pipe wrench and tube cutter
Cuts and reworks supply lines when a dielectric union or flex connector has corroded and needs replacing during the repair.
Methods & Techniques
Uniform Plumbing Code (UPC) temperature limits
We set residential tanks to 120 degrees per UPC guidance, which prevents scalding while still killing most bacteria in the tank. Commercial kitchens get 140 degrees with a mixing valve at the fixture.
ANSI Z21.10.1 gas appliance testing
Gas water heaters get tested to this standard for burner operation, gas valve function, and flue draft. It is the same protocol manufacturers use, and it catches problems a visual check misses.
Florida Building Code compliance
Every repair that touches gas piping, venting, or the TPR discharge line is done to Florida Building Code so the work passes inspection and your insurance stays valid.
EPA Section 608 handling
Any work involving refrigerant-charged heat pump water heaters follows EPA Section 608 rules for handling and recovery, which keeps the job legal and safe.
How Temperature Repair Works in Lehigh Acres
Lehigh Acres sits on some of the hardest water in Lee County, and that single fact drives most of the temperature problems we see. Calcium and magnesium settle out of the water and bake onto the bottom of the tank, forming an insulating layer that makes the burner or element run hotter and longer than it should. The result is water that swings between scalding and lukewarm, plus the rumbling noise that sounds like the tank is about to let go. Most homes here are single-story concrete block with the water heater in the garage or a utility closet, which makes access easy and keeps most repairs to a single visit. We work the Alabama Road Corridor, Lee Boulevard Corridor, and Joel Boulevard Corridor daily, and we know which neighborhoods have older 40-gallon tanks that are on their last legs. If you need affordable water heater temperature repair in Lehigh Acres, we quote the job before we start and stick to it. October starts our busy season as snowbirds return and find a tank that sat idle all summer, so book early if your water is running hot or cold.
Service Areas
Older housing stock with many 40-gallon gas tanks past the 10-year mark. Thermostat and thermocouple failures are the most common calls here.
Newer construction with mostly electric tanks. We see failed lower heating elements and sediment buildup from hard water within three to four years.
Well-water homes where iron and calcium are heavier than municipal supply. Anode rods here often need replacement by year five.
Family-heavy neighborhood with high hot-water demand. Dip tube failures show up as showers that go cold after five minutes.
Seasonal and snowbird properties where tanks sit idle for months. Pilot light and thermocouple issues spike in October and November.
Local Considerations
Hard water with high calcium and magnesium content
Sediment builds up fast, insulating the burner and causing temperature swings. We flush every tank we open and recommend an annual flush to keep heat transfer clean.
Hot, humid summers and mild winters
Tanks in garages see less freeze risk than northern states, but the heat and humidity accelerate corrosion on fittings and gas connections. We inspect and leak-test every connection.
Seasonal snowbird occupancy
Tanks that sit unused for months develop stale water and corroded thermocouples. We test and flush these units thoroughly before returning them to service.
Widespread use of 40 and 50-gallon tanks
Smaller tanks work harder in multi-person households, which shortens element and thermostat life. We size replacements correctly if a repair is not the right call.
Scalding Shower Fixed in One Visit
A homeowner in Lehigh Acres Central called because the shower water was hot enough to redden skin. The tank was set to 140 degrees and the thermostat had drifted another 8 degrees above that.
We replaced the failed thermostat, flushed two years of sediment, and set the tank to 120 degrees. Final tap reading was 119.6 degrees, verified with a digital gauge before we left.
Maintenance & Follow-up
Check the thermostat dial once a year and keep the tank set at 120. An annual flush keeps sediment from faking another thermostat failure.
A family in Varsity Lakes had showers that went cold after four minutes. The lower heating element had burned out and the dip tube had cracked, letting cold water mix into the hot outlet.
We replaced the lower element and dip tube with OEM parts, refilled the tank, and confirmed 122 degrees at the tub spout. The family now gets a full 15-minute hot shower.
Maintenance & Follow-up
Test your hot water monthly by filling a tub. If it cools before the tub fills, call before the element fails completely.
A homeowner in Sunshine Acres reported rumbling noises, rusty hot water, and inconsistent temperatures. The anode rod was 80 percent consumed and the tank had a thick sediment layer.
We replaced the anode rod, flushed the tank twice, and tested both thermostats. Rust cleared within 24 hours and the rumbling stopped. The tank should now last another three to five years.
Maintenance & Follow-up
On well water, have the anode rod checked every two years and flush the tank annually to stay ahead of mineral buildup.
What Temperature Repair Costs
Typical 2026 pricing in this area runs $180 to $450 for most temperature repairs, parts included. A thermostat replacement sits at the low end, a heating element or gas valve swap at the high end. Diagnostic fee is $89 and gets credited toward the repair if you approve the work. If we find a cracked tank or a repair that costs more than half a new unit, we tell you straight and quote the replacement instead of padding the repair bill.
Pricing Factors
Part that failed
A thermocouple is a $180 to $240 job. A thermostat runs $180 to $320. A heating element or gas valve runs $280 to $450 because the tank has to be drained and refilled.
Tank brand and age
Rheem, A. O. Smith, and Bradford White parts are stocked locally and priced normally. Older or discontinued models may need a special-order part, which adds a day and $40 to $90.
Gas versus electric
Electric repairs are usually faster and cheaper because there is no gas line to leak-test or burner to clean. Gas jobs add 30 to 45 minutes of safety testing to the labor.
Sediment severity
A heavily scaled tank needs a longer flush and sometimes a second drain cycle. That adds $60 to $120 but prevents the same failure from coming back within a year.
Access and location
Garage and utility closet tanks are straightforward. Tanks in tight attic spaces or behind finished walls add labor time and occasionally require a helper.
Emergency timing
After-hours and weekend calls carry a $75 to $125 dispatch premium. Standard weekday appointments between 8am and 5pm avoid that charge entirely.
Typical Investment Range
$180 - $450 for most temperature repairs, parts and labor included
Actual pricing varies based on project scope and requirements
Value You Receive
You are paying for a correct diagnosis, OEM parts, and a one-year labor warranty. A $250 thermostat job that lasts beats a $120 guess that fails in three months and costs you a second service call.
Frequently Asked Questions
Have questions? We have answers. If you don't see your question here, feel free to contact us.
Call UsWhy does my water heater have temperature problems in Lehigh Acres?
Hard water is the number one cause here. Calcium settles on the tank bottom, insulates the burner or element, and throws the thermostat reading off by 10 to 20 degrees. The second most common cause is a failed thermostat or heating element. We test both with a multimeter and a tap thermometer to confirm which one it is before quoting a repair.
How much does water heater temperature repair cost in Lehigh Acres?
Most jobs run $180 to $450 in 2026, parts and labor included. A thermocouple or thermostat replacement sits at the low end; a heating element or gas valve swap sits at the high end. The $89 diagnostic fee is credited toward the repair if you approve the work, so you are not paying twice for the same visit.
Can I get same day water heater temperature repair in Lehigh Acres?
Yes, in most cases. Call before noon and we can usually have a technician at your door within two to four hours for emergency water heater temperature repair Lehigh Acres FL calls. We stock thermostats, thermocouples, and heating elements for Rheem, A. O. Smith, and Bradford White tanks, so the repair typically finishes in one visit.
How do I adjust my water heater temperature in Lehigh Acres?
On a gas tank, turn the dial on the front of the gas valve to the 120-degree mark, usually labeled with a triangle or the letter B. On electric tanks, shut off the breaker first, remove the upper access panel, and turn the thermostat screw with a flathead until it reads 120. If the dial is already at 120 and your water is still off, the thermostat has failed and needs replacement.
Licensed, Insured, and Reviewed
Certifications
Customer Reviews
Our water was scalding hot for a week and I could not figure out why. They came out the same afternoon, tested the thermostat, replaced it, and set the tank to 120. Took about an hour and the price matched the quote exactly.
Showers kept going cold after five minutes. Turned out to be the lower element and dip tube. They had both parts on the truck and fixed it in one visit. Hot water has been perfect for three months now.
Called about a rumbling tank and rusty water in Sunshine Acres. They replaced the anode rod and flushed the tank twice. The noise stopped and the water runs clear. Honest about what needed doing and what could wait.
Related Services
Explore our other professional services
Gas Water Heater Repair
Gas tanks fail differently than electric ones, usually through a bad thermocouple or sticking gas valve. We test both to ANSI Z21.10.1 and restore steady temperature in one visit for Lehigh Acres homes.
Gas Water Heater RepairElectric Water Heater Repair
Electric temperature problems almost always trace to a failed heating element or thermostat. We ohm out both elements with a multimeter and replace the bad part with an OEM match the same day.
Electric Water Heater RepairTankless Water Heater Repair
Tankless units throw temperature errors when the heat exchanger scales up or the flow sensor drifts. We descale Rinnai and Navien units and recalibrate outlet temperature to within two degrees of setpoint.
Tankless Water Heater RepairRheem Water Heater Repair
Rheem tanks are common across Lehigh Acres, and we stock their thermostats, elements, and thermocouples. Temperature swings on a Rheem usually mean a failed lower element or a thermostat that has drifted past 130 degrees.
Rheem Water Heater RepairA. O. Smith Water Heater Repair
A. O. Smith gas and electric tanks use specific thermostat part numbers, and we carry them. If your A. O. Smith runs hot or cold, we test the thermostat and gas valve and replace what failed.
A. O. Smith Water Heater RepairBradford White Water Heater Repair
Bradford White tanks hold temperature well until the thermocouple or element wears out. We diagnose with a thermocouple tester and element wrench, then restore your tank to a steady 120 degrees.
Bradford White Water Heater RepairRinnai Water Heater Repair
Rinnai tankless heaters display error codes when outlet temperature drifts. We descale the heat exchanger, test the flow sensor, and recalibrate so your hot water holds steady through a long shower.
Rinnai Water Heater RepairNavien Water Heater Repair
Navien units need periodic descaling in hard water areas like Lehigh Acres. When temperature swings appear, we flush the exchanger, check the mixing valve, and reset the outlet temperature to spec.
Navien Water Heater RepairWater Heater Not Producing Hot Water
No hot water at all is usually a thermocouple, gas valve, or heating element failure. We test each part in sequence and replace the failed one, often restoring hot water within two hours.
Water Heater Not Producing Hot WaterWater Heater Leaking Water
A leak plus temperature problems often means the tank itself has failed. We inspect the TPR valve, fittings, and tank seams to tell you whether a repair is realistic or a replacement is the smarter call.
Water Heater Leaking WaterWater Heater Making Rumbling Noises
Rumbling is sediment boiling under the burner, and it always comes with temperature swings. We flush the tank, inspect the anode rod, and reset the thermostat to stop the noise and restore even heat.
Water Heater Making Rumbling NoisesWater Heater Takes Too Long to Heat
A tank that takes an hour to recover usually has a scaled bottom or a weak lower element. We flush the tank and test the element, which typically cuts recovery time back to 20 or 30 minutes.
Water Heater Takes Too Long to HeatWater Heater Runs Out of Hot Water
Running out fast points to a broken dip tube or a failed lower element. We inspect the dip tube with a camera and replace it along with any failed element so your tank holds heat through a full shower.
Water Heater Runs Out of Hot WaterWater Heater Pilot Light Keeps Going Out
A pilot that will not stay lit is a thermocouple problem nine times out of ten. We test the millivolt output and replace the thermocouple, usually in 30 minutes, restoring full gas operation.
Water Heater Pilot Light Keeps Going OutWater Heater Burner Not Working
A burner that will not fire means the gas valve, thermocouple, or air supply has failed. We test each component, clean the burner and flue, and confirm proper flame before we leave.
Water Heater Burner Not WorkingWater Heater Heating Element Repair
Failed elements cause lukewarm water and slow recovery. We replace both upper and lower elements with OEM parts, torque them properly, and verify the new temperature at the tap.
Water Heater Heating Element RepairWater Heater Thermostat Repair
Thermostats drift, weld closed, or fail open, and all three cause temperature problems. We test both thermostats on electric tanks and replace the failed one, then reset the tank to 120 degrees.
Water Heater Thermostat RepairWater Heater Gas Valve Repair
A sticking gas valve causes scalding water or no heat at all. We test the valve, replace it when needed, and leak-test every connection to Florida Building Code before restoring gas.
Water Heater Gas Valve RepairWater Heater Pressure Relief Valve Leaking
A weeping TPR valve often means the tank is running too hot or pressure is too high. We test the valve, check the expansion tank, and correct the temperature setting that caused it.
Water Heater Pressure Relief Valve LeakingWater Heater Anode Rod Problems
A consumed anode rod lets the tank corrode from the inside, which shows up as rusty hot water and odd smells. We inspect the rod with a camera and replace it before the tank is ruined.
Water Heater Anode Rod ProblemsWater Heater Low Hot Water Pressure
Low pressure on the hot side usually means sediment in the nipples or a failing dip tube. We flush the tank and clear the fittings, which restores full flow at every hot tap.
Water Heater Low Hot Water PressureWater Heater Discolored or Rusty Water
Rusty hot water points to anode rod failure or tank corrosion. We inspect the rod and tank interior, replace the rod if the tank is still sound, and tell you honestly if replacement is the better call.
Water Heater Discolored or Rusty WaterWater Heater Strange Smell in Hot Water
A sulfur smell usually means bacteria reacting with a spent anode rod. We replace the rod, disinfect the tank, and flush the system, which clears the odor within a day.
Water Heater Strange Smell in Hot WaterEmergency Water Heater Repair
No hot water or scalding water is an emergency, especially with kids in the house. We run 24/7 water heater temperature repair Lehigh Acres FL calls with a two-hour response window for most addresses.
Emergency Water Heater RepairResidential Water Heater Repair
From a single-family home in Lehigh Park to a duplex near Homestead, we handle residential temperature problems on gas, electric, and tankless systems with same-day service.
Residential Water Heater RepairCommercial Water Heater Repair
Restaurants and small businesses need hot water at 140 degrees with a mixing valve at the fixture. We service commercial tanks and verify temperature at every outlet before signing off.
Commercial Water Heater RepairWhat Lehigh Acres Homeowners Say
Real experiences from customers who chose our Water Heater Temperature Problems services
"Our shower water was hot enough to hurt. I called in the morning and they were here by early afternoon. The technician tested the thermostat, showed me the reading was 148 degrees, replaced it, and set it to 120. He also flushed the tank and showed me the sediment that came out. Fair price, no upsell."
Maria R.
Homeowner, Lehigh Acres Central
"I manage three rentals and one tenant kept complaining about cold showers. They diagnosed a bad lower element and a cracked dip tube, replaced both the same day, and gave me a written warranty for my records. I have used them on two other units since and the pricing has been consistent every time."
Darnell T.
Landlord, Joel Boulevard Corridor
"We had rumbling noises and rusty hot water for weeks. They inspected the anode rod with a camera, showed me it was almost gone, and replaced it along with a full flush. The rust cleared in a day and the tank is quiet again. They told me honestly the tank has a few more years left instead of pushing a replacement."
Susan K.
Homeowner, Varsity Lakes
Get Your Water Heater Temperature Problems Lehigh Acres FL Fixed Today
Scalding or lukewarm water is not something to live with. Call us at (239) 230-9988 and we will have a licensed technician at your door, usually within two hours. Flat pricing quoted before we start, one-year labor warranty on every repair.