Water Heater Anode Rod Problems Lehigh Acres FL
Corroded rods, rusty water, and rotten-egg smells fixed fast
Water Heater Anode Rod Problems Lehigh Acres FL usually show up as rusty hot water, a sulfur smell, or a tank that suddenly quits. Your anode rod is the sacrificial metal inside the tank that absorbs corrosion so the steel shell does not. Once it is gone, the tank starts eating itself. We inspect, test, and replace it before that happens, and we handle anode rod replacement in Lehigh Acres for gas, electric, and tankless systems.
Water Heater Anode Rod Problems Lehigh Acres FL Explained
Water Heater Anode Rod Problems Lehigh Acres FL start with one part you never see: the anode rod. It is a magnesium or aluminum rod threaded into the top of the tank, and it corrodes on purpose so the steel lining does not. In our water, that rod can be gone in three to five years. When it is, the tank rusts from the inside out, hot water turns brown, and the smell gets bad. We pull the rod, inspect it with an inspection camera, and tell you honestly whether a replacement saves the tank or whether the tank is already too far gone.
Most Lehigh Acres homes sit on well water or hard municipal supply, and both chew through anode rods faster than the national average. If your hot water smells like sulfur or your fixtures stain, you are probably looking at a corroded anode rod Lehigh Acres homeowners deal with every week. We see it constantly in homes built through the 1990s and 2000s off Joel Boulevard and Lee Boulevard, where original tanks are still running on the factory rod. A $180 to $350 replacement now beats a $1,400 tank swap later.
Why Fix the Anode Rod Early
Replacing a spent anode rod is the cheapest way to add years to a water heater. Here is what you get when you call us before the tank rusts through.
Stop Tank Corrosion
A fresh magnesium or aluminum anode rod takes the corrosion hit instead of your tank lining. We match the rod to your water chemistry, install it with a proper anode rod socket, and torque it to spec. That single part can add four to six years to a tank that is otherwise healthy, which is why we push anode rod replacement Lehigh Acres homeowners can schedule before damage spreads.
Kill the Sulfur Smell
That rotten-egg odor in hot water is usually a reaction between bacteria and a spent anode rod. We pull the old rod, sanitize the tank with a chlorine flush, and install a zinc or aluminum-zinc rod that resists the reaction. Most customers notice the smell is gone within one heating cycle, usually the same day.
Protect Your Fixtures
Rusty water does not stay in the tank. It travels through your dip tube, supply lines, and every faucet aerator in the house. Brown staining on sinks, tubs, and laundry is a sign the rod failed months ago. Replacing it stops the rust at the source and keeps sediment out of your fixtures and washing machine.
Avoid Emergency Replacement
A tank that rusts through leaks from the bottom, usually at 6 a.m. on a Saturday. Emergency anode rod replacement Lehigh Acres FL calls cost far more than a planned rod swap, and you still need a new tank. We check the rod during any tune-up so you are never surprised by a flooded garage or closet floor.
Our Anode Rod Service Process
We keep the job simple: find the problem, show you what we found, fix it, and prove it works before we leave. Most anode rod jobs take 60 to 90 minutes on site.
Phone Diagnosis
You call (239) 230-9988 and describe what you are seeing: rusty water, sulfur smell, rumbling, or no hot water. We ask about the tank age, fuel type, and brand, whether it is Rheem, A. O. Smith, Bradford White, or State Water Heaters. That five-minute call tells us whether to bring a replacement rod, a full tank, or both.
On-Site Inspection
We shut off the gas or power, drain a few gallons, and pull the anode rod with an anode rod socket and pipe wrench. If the rod is coated in white calcium or eaten down to the core wire, it is done. We also check the TPR valve, thermocouple, heating element, and dip tube while the tank is open, using a multimeter and inspection camera.
Water and Tank Testing
We test your water hardness and check for sulfur bacteria, because the right rod depends on it. Magnesium rods work well in soft water; aluminum or aluminum-zinc rods last longer in hard Lehigh Acres water. If sediment has built up, we flush the tank through the drain valve with a pressure gauge on the hose to confirm flow.
Rod Replacement
We thread in the correct anode rod, seal it with fresh Teflon tape or pipe dope, and torque it to the manufacturer spec. On gas units we recheck the thermocouple and flue pipe; on electric units we verify the heating element and thermostat. The tank refills, and we bleed the air from every hot faucet in the house.
Test and Walkthrough
We fire the burner or energize the element and watch the tank come up to temperature, usually 120 to 140 degrees. We show you the old rod, explain what it tells us about the tank's remaining life, and note the replacement date on the tank label. You get a written summary and a reminder for the next rod check.
Anode Rod Expertise You Can Use
Our technicians work on residential and commercial water heaters every day, from 40-gallon gas tanks in Lehigh Park garages to 100-gallon commercial units along the Alabama Road Corridor. We hold a Florida state plumbing license and a Lee County contractor license, and we follow the Uniform Plumbing Code and Florida Building Code on every install. We are EPA Section 608 certified for refrigerant work and OSHA safety certified for confined-space and gas-line jobs. We also carry NATE certification on the mechanical side. That matters because anode rod problems rarely travel alone. A failed rod usually comes with sediment buildup, a tired thermocouple, or a TPR valve that is starting to weep. We catch all of it in one visit.
- Florida state plumbing license and Lee County contractor license on every job
- EPA Section 608 and OSHA safety certifications for gas and confined-space work
- NATE-certified technicians who service Rheem, A. O. Smith, Bradford White, Rinnai, and Navien units
- We follow Uniform Plumbing Code and Florida Building Code on every anode rod and tank install
- Work is performed to ANSI Z21.10.1 and CSA certification standards for gas-fired storage heaters
Why Lehigh Acres Calls Us for Anode Rod Problems
We are a local shop, not a call center. When you book an anode rod job, the technician who shows up is the one who does the work and explains it in plain language.
Same-Day Service Available
Call before noon and we can usually get to your Lehigh Acres home the same day. We stock magnesium, aluminum, and aluminum-zinc rods on every truck, plus common Rheem and A. O. Smith replacement parts. That means fewer return trips and a faster fix for rusty water or sulfur smells.
Straight Answers, No Upsell
If your tank has years left, we replace the rod and send you on your way. If the tank lining is already compromised, we tell you that too, with photos from the inspection camera. You decide. We do not push a new tank when a $200 rod solves the problem.
Local Water Knowledge
Lehigh Acres water is hard, and well water in the Sunshine Acres and Homestead areas can be harder still. We test hardness and sulfur on site, then pick the rod that lasts longest in your specific supply. That is how we get anode rod replacement Lehigh Acres customers to go five or more years between swaps instead of two.
24/7 Emergency Response
Tanks do not wait for business hours. If your water heater is leaking and you need emergency anode rod replacement Lehigh Acres FL, call (239) 230-9988 any time. We answer, we dispatch, and we shut the water down before the damage spreads to drywall or flooring.
What Our Anode Rod Service Includes
Every anode rod visit covers the rod itself plus the checks that keep the rest of the tank healthy. If we find a separate problem, like a failed gas valve or a leaking TPR valve, we quote it before we touch it. No surprise line items.
What's Included
Full Anode Rod Inspection
We pull the existing rod and inspect it end to end. A rod eaten below 50 percent of its original diameter is replaced. We photograph it so you can see exactly why the swap was needed.
Correct Rod Selection
Magnesium, aluminum, or aluminum-zinc, chosen based on your water hardness and sulfur levels. We do not guess. The wrong rod can make a sulfur smell worse or corrode away in 18 months.
Tank Flush and Sediment Removal
While the tank is open we flush sediment through the drain valve. Sediment insulates the burner, causes rumbling noises, and shortens tank life. A clean tank heats faster and holds more hot water.
Safety Valve and Fitting Check
We test the TPR valve, check the dielectric unions and supply connections, and look at the flue pipe on gas units. A sticky TPR valve or a loose union can turn a small job into a flooded closet.
Replacement Date Logged
We write the install date and rod type on the tank label so the next technician, or you, knows exactly when it was done. That record makes future maintenance simple.
Anode Rod Problems We Solve in Lehigh Acres
Most anode rod failures fall into a handful of patterns. Here are the ones we see most often in Lehigh Acres, and what happens if you let them run.
Hot water smells like rotten eggs
Sulfur bacteria feed on the hydrogen gas a spent magnesium rod produces. The smell gets into dishes, laundry, and showers, and it will not go away on its own.
We pull the magnesium rod, sanitize the tank, and install an aluminum-zinc rod that does not feed the bacteria. Most customers notice the difference the same day, and the smell stays gone for years.
Rusty or brown hot water
Brown water means the tank lining is already corroding. Left alone, the tank will rust through and leak, usually from the bottom where you cannot see it.
We inspect the tank interior with an inspection camera. If the lining is still sound, a new anode rod stops the rust immediately. If it is too far gone, we tell you straight and quote a replacement tank.
Rumbling and popping noises
Sediment builds up when the anode rod is spent and the water chemistry shifts. The burner heats through a layer of scale, which wastes gas and shortens tank life.
We flush the tank, replace the rod, and check the heating element or burner. A clean tank with a fresh rod runs quieter and heats faster, often cutting a few dollars a month off the gas bill.
Anode rod corroded through in under three years
Hard or sulfur-heavy well water eats rods fast. If yours fails early, the next one will too unless the rod type changes.
We test your water on site and switch to a rod rated for your chemistry, often aluminum-zinc or a powered anode. That gets you back to a normal five-year cycle instead of replacing rods every other year.
When Lehigh Acres Homeowners Call Us
A homeowner in Lehigh Acres Central notices the hot water smells like sulfur only in the morning, and the tank is eight years old.
We pull the original magnesium rod, which is down to the core wire, sanitize the tank, and install an aluminum-zinc rod. We also flush the sediment that has collected over eight years.
The smell is gone by the next morning, and the tank gets another four to six years of service instead of a premature replacement.
A family in Mirror Lakes sees brown water from the hot tap only, and the cold water runs clear.
Brown hot water points straight at the tank, not the supply. We inspect the rod and tank lining with a camera, replace the corroded rod, and flush the tank until the water runs clear.
Hot water runs clear within a day, and no rusty water reaches the washing machine or dishwasher.
A landlord with a duplex in Greenbriar needs anode rod replacement on two 50-gallon gas tanks before new tenants move in.
We service both tanks in one trip, replacing rods, testing thermocouples and TPR valves, and flushing each tank. We log the replacement dates on both labels.
Both units pass a hot-water test the same afternoon, and the landlord has a written record for the next inspection.
A homeowner off the Joel Boulevard Corridor has well water and replaces anode rods every two years.
We test hardness and sulfur, then install a powered anode that does not corrode away. We also check the expansion tank and pressure gauge while we are there.
The rod stops consuming itself, and the homeowner stops paying for a replacement every other year.
Tools and Methods We Use
Tools & Equipment
Anode rod socket
The correct six-point socket grabs the rod hex without rounding it. A rounded anode rod head turns a 60-minute job into a two-hour extraction.
Inspection camera
We drop the camera into the tank through the anode port to see the lining, sediment level, and dip tube condition. That is how we tell you honestly whether the tank is worth saving.
Multimeter and thermocouple tester
On gas units we verify the thermocouple and gas valve readings before we button the tank back up. On electric units we test the heating element and thermostat for continuity.
Pipe wrench and tube cutter
Used for supply lines, dielectric unions, and any corroded fittings that need replacing while the tank is open. We keep common sizes on the truck.
Pressure gauge and flue brush
The gauge confirms flow during the tank flush. The flue brush clears the flue pipe on gas heaters so combustion gases vent properly after the job.
Methods & Techniques
Uniform Plumbing Code (UPC) compliance
Every anode rod replacement and tank connection is made to UPC standards, including proper dielectric unions and backflow protection. That keeps the install legal and insurable.
Florida Building Code and ANSI Z21.10.1
Gas-fired storage heaters must meet ANSI Z21.10.1 and the Florida Building Code for venting and combustion air. We verify both before we call a job complete.
Water chemistry matching
We test hardness and sulfur on site, then choose magnesium, aluminum, or aluminum-zinc. The right rod lasts five or more years; the wrong one can fail in 18 months.
Torque-to-spec installation
Anode rods are torqued to the manufacturer spec with fresh Teflon tape or pipe dope. Over-tightening cracks the tank boss; under-tightening leaks. We do it once, correctly.
How Anode Rod Service Runs in Lehigh Acres
Lehigh Acres sits on a mix of municipal and well water, and both are hard enough to shorten anode rod life. Homes built through the 1990s and 2000s, especially around Lehigh Park, Varsity Lakes, and Country Club Estates, are still running original tanks with factory rods that are long past due. We see sulfur bacteria more often in well-served pockets near Sunshine Acres and Homestead, where a standard magnesium rod makes the smell worse instead of better. Summer is our busiest season because hot garages and closets push tank temperatures up, and that accelerates corrosion. Fall and winter are the right time to schedule a rod check before the holiday guest rush. If you search for water heater anode rod problems near me Lehigh Acres, you will find plenty of general advice. What you need is someone who knows your water. We test it, match the rod, and log the date so the next check is easy. We also handle 24/7 anode rod replacement Lehigh Acres FL calls when a tank lets go at the worst possible time.
Service Areas
Older housing stock with original tanks. Most anode rods here are original or one replacement deep, and sediment is common.
A mix of well and city water. We see more rusty-hot-water calls here than sulfur calls, which usually means the tank lining is already going.
Well water with higher sulfur content. Standard magnesium rods make the smell worse, so we switch these homes to aluminum-zinc.
Many rental and multi-unit properties. We batch anode rod replacements here so landlords get both tanks done in one trip.
Newer builds with 50-gallon gas tanks. Factory rods are usually due at the five-year mark, and we catch most of them before they fail.
Local Considerations
Hard municipal and well water across Lehigh Acres
Hard water coats the anode rod in calcium, which slows its protective action and shortens its life. We test hardness and choose a rod rated for the reading.
Sulfur bacteria in well-served pockets
Sulfur reacts with magnesium rods to create the rotten-egg smell. We sanitize the tank and install aluminum-zinc rods in these homes.
Hot garages and closets in summer
Higher ambient temperatures push tank temperatures up and accelerate corrosion. Summer is when we see the most sudden rod failures.
Aging housing stock from the 1990s and 2000s
Original tanks in these homes are at or past the point where the factory rod is spent. A rod check now is far cheaper than a tank replacement later.
Sulfur Smell Gone in One Visit
A Lehigh Acres Central homeowner had hot water that smelled like rotten eggs every morning. The tank was eight years old, and the original magnesium rod was down to the core wire. Sediment had built up to the lower element.
We pulled the spent rod, sanitized the tank, flushed the sediment, and installed an aluminum-zinc rod. The smell was gone by the next morning, and the tank is now on a five-year rod cycle instead of a replacement.
Maintenance & Follow-up
Check the rod every three years and keep the tank temperature at 130 degrees or below. Both slow sulfur bacteria and extend rod life.
A family in Mirror Lakes had brown water from every hot tap, while the cold water ran clear. The tank was ten years old, and the anode rod had corroded completely. The lining was starting to pit but had not failed.
We replaced the rod, flushed the tank twice, and replaced the dip tube, which had cracked. Hot water ran clear within a day, and the family avoided a full tank replacement for another four years.
Maintenance & Follow-up
Flush the tank once a year and check the anode rod every three years. Rusty water that comes back means the lining is failing and the tank needs replacement.
A landlord in Greenbriar had two 50-gallon gas tanks in a duplex, both with original rods and no service records. Tenants had complained about rumbling noises and slow hot water recovery.
We serviced both tanks in one visit, replacing rods, flushing sediment, and testing thermocouples and TPR valves. Both units passed a hot-water test the same afternoon, and we logged the replacement dates on each tank.
Maintenance & Follow-up
Schedule a rod check every three years on rental units. Logging the date on the tank label keeps the next service simple and prevents missed maintenance.
What Anode Rod Service Costs
Typical 2026 pricing for anode rod replacement in Lehigh Acres runs $180 to $350 for a standard residential tank, including the rod, labor, and tank flush. Powered anodes and commercial tanks cost more. If the tank lining is already compromised, we tell you before doing any work, and a replacement tank is a separate conversation. We quote the job upfront on the phone or at the door, and the price does not change unless you approve additional work. Emergency and after-hours calls carry a higher rate, which we state before we dispatch.
Pricing Factors
Rod type and material
A standard magnesium or aluminum rod is the least expensive option. Aluminum-zinc rods cost a bit more but last longer in sulfur water. Powered anodes cost the most but never corrode away.
Tank size and access
A 40-gallon tank in an open garage is a quick job. A 75-gallon tank in a tight closet with limited clearance takes longer and may need extra labor to reach the anode port.
Sediment and flush time
Heavy sediment means a longer flush and sometimes a second visit. We include a standard flush in the base price and quote extra time if the tank is badly scaled.
Related repairs found on site
A failed thermocouple, a leaking TPR valve, or a cracked dip tube adds to the bill. We quote each item before we touch it, so you can approve or decline.
Emergency or after-hours timing
Weekend and overnight calls carry a higher rate because we dispatch a technician immediately. Scheduled weekday work is the most affordable option.
Typical Investment Range
$180 - $350 for standard residential anode rod replacement; $350 - $650 for powered anodes or commercial tanks
Actual pricing varies based on project scope and requirements
Value You Receive
A $200 rod replacement can add four to six years to a tank that would otherwise cost $1,200 to $1,800 to replace. It is the cheapest insurance you can buy for a water heater, and we log the date so the next check is easy.
Frequently Asked Questions
Have questions? We have answers. If you don't see your question here, feel free to contact us.
Call UsWhy is my water heater anode rod causing problems in Lehigh Acres?
Your anode rod is doing its job, and that is the problem. It corrodes on purpose to protect the tank lining, and in Lehigh Acres hard water it can be gone in three to five years. Once it is spent, the tank starts rusting, hot water turns brown, and sulfur bacteria produce a rotten-egg smell. Replacing the rod stops all three.
How much does anode rod replacement cost in Lehigh Acres?
Most residential jobs run $180 to $350 in 2026, including the rod, labor, and a tank flush. Powered anodes and commercial tanks run $350 to $650. The price depends on rod type, tank size, and access. We quote the job before we start, and the number does not change unless you approve extra work.
Who replaces water heater anode rods in Lehigh Acres FL?
We do. Lehigh Acres WaterCore Repair handles anode rod replacement for gas, electric, and tankless systems across Lehigh Acres and Lee County. Our technicians hold a Florida state plumbing license and a Lee County contractor license, and we stock magnesium, aluminum, and aluminum-zinc rods on every truck. Call (239) 230-9988 to book.
Can I get same day anode rod replacement in Lehigh Acres?
Yes, in most cases. Call before noon and we can usually get to your home the same day, especially for sulfur smells or rusty water. We stock common rods and parts on the truck, so most jobs finish in one visit. Emergency and after-hours calls are also available 24/7 at (239) 230-9988.
Licensed, Certified, and Local
Certifications
Customer Reviews
Our hot water smelled like sulfur for months. Two other plumbers told us we needed a new tank. These guys pulled the anode rod, showed us it was eaten away, and replaced it with an aluminum-zinc rod. Smell was gone the next day. Saved us over a thousand dollars.
Called at 9 a.m. about rusty hot water in our Mirror Lakes home. They had a tech out by 1 p.m. the same day. He flushed the tank, replaced the rod, and even showed us photos of the inside. Fair price, no upsell. Highly recommend.
We manage several rental properties in Greenbriar and needed anode rods replaced on two tanks. They did both in one trip and logged the dates on the labels. Professional, on time, and the price matched the quote exactly. We will use them again.
Related Services
Explore our other professional services
Gas Water Heater Repair
Gas tanks have the same anode rod as electric units, plus a burner, thermocouple, and flue to check. When we replace a rod on a gas heater in Lehigh Acres, we also verify combustion and venting to ANSI Z21.10.1.
Gas Water Heater RepairElectric Water Heater Repair
Electric tanks rely on heating elements and thermostats that fail more often once the anode rod is gone. We test both with a multimeter during any rod replacement, so you are not back in a month for a second repair.
Electric Water Heater RepairTankless Water Heater Repair
Tankless units do not have a traditional anode rod, but they do scale up in hard Lehigh Acres water. We descale the heat exchanger and check the inlet filter, which solves many of the same symptoms.
Tankless Water Heater RepairRheem Water Heater Repair
Rheem tanks use a specific anode rod thread and length. We stock Rheem-compatible rods and parts, so your Lehigh Acres home gets the right fit the first time without a return trip.
Rheem Water Heater RepairA. O. Smith Water Heater Repair
A. O. Smith tanks often hide the anode port behind a top cover. We know where to look, and we carry the correct socket and rod for these units, which saves time and avoids damage to the tank top.
A. O. Smith Water Heater RepairBradford White Water Heater Repair
Bradford White heaters use a combination anode rod that also holds the hot outlet. Replacing it takes care and the right tools. We handle these regularly in Lehigh Acres and test the outlet fitting afterward.
Bradford White Water Heater RepairRinnai Water Heater Repair
Rinnai tankless heaters need periodic descaling in our water. If your unit is throwing a scale code or losing hot water pressure, we flush the heat exchanger and check the gas and water connections.
Rinnai Water Heater RepairNavien Water Heater Repair
Navien combi and tankless units have their own scale and flow issues. We service them with manufacturer-approved descaling and check the recirculation pump, which often fails alongside scale buildup.
Navien Water Heater RepairWater Heater Not Producing Hot Water
A spent anode rod rarely causes no-hot-water on its own, but it often travels with a failed thermocouple, element, or gas valve. We diagnose the whole tank, not just the rod, so the real cause gets fixed.
Water Heater Not Producing Hot WaterWater Heater Leaking Water
Leaks from the top of the tank often start at the anode rod threads. We pull the rod, reseal it, and check the TPR valve and unions. If the tank itself is leaking, we tell you straight and quote a replacement.
Water Heater Leaking WaterWater Heater Making Rumbling Noises
Rumbling means sediment. A spent anode rod lets scale build up faster, so we flush the tank and replace the rod together. That quiets the tank and restores hot water recovery.
Water Heater Making Rumbling NoisesWater Heater Takes Too Long to Heat
Sediment and a failing element both slow recovery. We check the rod, flush the tank, and test the element or burner, which usually brings recovery time back to normal.
Water Heater Takes Too Long to HeatWater Heater Runs Out of Hot Water
A tank that runs cold early often has a broken dip tube or heavy sediment. We inspect both during anode rod service and replace the dip tube if it has cracked, which is common in older Lehigh Acres tanks.
Water Heater Runs Out of Hot WaterWater Heater Pilot Light Keeps Going Out
A dirty thermocouple or a failing gas valve causes this. We test both with a thermocouple tester during any gas tank service, so you are not relighting the pilot every week.
Water Heater Pilot Light Keeps Going OutWater Heater Burner Not Working
Burner problems on gas tanks often trace to the thermocouple, gas valve, or a clogged burner orifice. We diagnose and repair these alongside anode rod work to keep the tank running safely.
Water Heater Burner Not WorkingWater Heater Heating Element Repair
Electric elements fail faster once sediment covers them. We replace elements with the correct wattage and check the thermostat at the same time, which prevents a repeat failure.
Water Heater Heating Element RepairWater Heater Thermostat Repair
A thermostat that reads wrong causes scalding or lukewarm water. We test it with a multimeter and replace it if needed, then verify the tank holds 120 to 140 degrees.
Water Heater Thermostat RepairWater Heater Gas Valve Repair
Gas valves fail closed or stick open. We test inlet and outlet pressure, replace the valve if needed, and check the sediment trap and flue before returning the tank to service.
Water Heater Gas Valve RepairWater Heater Pressure Relief Valve Leaking
A weeping TPR valve can mean excess pressure or a failed valve. We test it during anode rod service and replace it if it does not reseat, which protects the tank from a rupture.
Water Heater Pressure Relief Valve LeakingWater Heater Temperature Problems
Water that is too hot or too cold usually points at the thermostat or a crossed dip tube. We diagnose both and set the tank to a safe, consistent temperature before we leave.
Water Heater Temperature ProblemsWater Heater Low Hot Water Pressure
Low pressure on the hot side only often means sediment in the nipples or a failing dip tube. We flush the tank and check the supply lines during anode rod service.
Water Heater Low Hot Water PressureWater Heater Discolored or Rusty Water
Rusty hot water is the classic sign of a spent anode rod. We replace the rod, flush the tank, and inspect the lining with a camera to tell you whether the tank has years left or is on its way out.
Water Heater Discolored or Rusty WaterWater Heater Strange Smell in Hot Water
Sulfur smells come from bacteria reacting with a magnesium rod. We sanitize the tank and switch to an aluminum-zinc rod, which solves the smell for most Lehigh Acres well-water homes.
Water Heater Strange Smell in Hot WaterEmergency Water Heater Repair
When a tank lets go at night or on a weekend, we answer. Call (239) 230-9988 for emergency anode rod replacement or any urgent water heater issue in Lehigh Acres and Lee County.
Emergency Water Heater RepairResidential Water Heater Repair
Most of our anode rod work is on residential tanks from 40 to 80 gallons. We handle gas, electric, and tankless units in homes across Lehigh Acres, from Lehigh Park to Richmond Park.
Residential Water Heater RepairCommercial Water Heater Repair
Commercial tanks run hotter and harder, so anode rods deplete faster. We service commercial units along the Lee Boulevard Corridor and Alabama Road Corridor with minimal downtime for your business.
Commercial Water Heater RepairWhat Our Customers Say
Real experiences from customers who chose our Water Heater Anode Rod Problems services
"The sulfur smell in our hot water was so bad we stopped using the guest bathroom. A neighbor recommended these guys. The technician pulled the anode rod, and it was basically gone. He sanitized the tank and put in a different type of rod. No smell since, and that was over a year ago. Fair price and no pressure to buy a new tank."
Maria G.
Homeowner, Lehigh Acres Central
"Brown water from the hot tap had us worried the tank was about to blow. They came out the same afternoon, inspected the inside with a camera, and showed us the lining was still okay. Replaced the anode rod and flushed the tank twice. Water runs clear now. Honest work and they did not try to sell us a tank we did not need."
Darnell W.
Homeowner, Mirror Lakes
"I manage six rental units and anode rods are always getting missed. These guys serviced two tanks in one trip, replaced the rods, tested the TPR valves, and wrote the dates on the tanks. Tenants stopped complaining about rumbling noises. They are now my go-to for water heater work in Lehigh Acres."
Karen P.
Property Manager, Greenbriar
Get Your Anode Rod Checked Today
Rusty water, sulfur smells, and rumbling noises do not fix themselves. Call Lehigh Acres WaterCore Repair at (239) 230-9988 for same-day anode rod service in Lehigh Acres, FL. We are licensed, insured, and local to Lee County.